D800 Iphone Tplink connection

[MartinRichter]

Hey There,

i cant connect to my D800 with qdslrDashboard App for Iphone 6.

Informations:
TP-Link bought new, without system.
install the new version 0.13
activate lan
router is on camera too
router version 2 in AP mode

connection iphone ==> Tplink is active

connection windows pc usb and qdslr is okay

but connection Iphone Tplink qdslr is not okay cant connect

in qdslr app
router ip adress 192.168.1.1
port 4757

where´s the problem?
please HELP

best regards
Martin

[GonzoG]

First check if camera is properly connected to router.
Here you have instructions how to do it: http://dslrdashboard.info/phpBB3/viewto ... f=5&t=1330

[MartinRichter]

Sep 8 15:45:56 OpenWrt kern.info kernel: [ 124.420000] usb 1-1: new high-speed USB device number 5 using ehci-platform
Dec 4 14:54:18 OpenWrt kern.info kernel: [ 190.210000] usb 1-1: USB disconnect, device number 5
Dec 4 14:54:20 OpenWrt kern.info kernel: [ 192.300000] usb 1-1: new high-speed USB device number 6 using ehci-platform
Dec 4 14:54:21 OpenWrt kern.err kernel: [ 192.900000] usb 1-1: device not accepting address 6, error -71
Dec 4 14:54:21 OpenWrt kern.info kernel: [ 193.020000] usb 1-1: new high-speed USB device number 7 using ehci-platform

thats my last system log

the date jump to the sep. 8 2015 always i must synch with browser every time

[GonzoG]

There is something wrong with ddserver. Probably you havn't flashed it correctly.

To be sure flash both FW images again (although sys-upgrade should be enough) and try if it's working.

[MartinRichter]

There is something wrong with ddserver. Probably you havn't flashed it correctly.

To be sure flash both FW images again (although sys-upgrade should be enough) and try if it's working.

sorry i dont know what to do? FW images?

[MartinRichter]

I dont know what to do?

flash both FW Images ????

[GonzoG]

FW = firmware.

Flash both images provided by Zoltan ( "factory" and "sysupgrade"):
http://dslrdashboard.info/downloads/

[cathy]

http://youtu.be/Our-AxmrDJM

[SirChaddy]

I am having a similar issue. My messages are the same:

Sep 8 16:04:23 OpenWrt kern.info kernel: [ 1231.690000] usb 1-1: new high-speed USB device number 12 using ehci-platform
Sep 8 16:04:24 OpenWrt kern.err kernel: [ 1232.290000] usb 1-1: device not accepting address 12, error -71
Sep 8 16:04:24 OpenWrt kern.info kernel: [ 1232.410000] usb 1-1: new high-speed USB device number 13 using ehci-platform

The interesting thing is that I have managed to connect the D800 correctly and copy over some images and control the camera through dashboard. However, the vast majority of the times when I start the router (hard restart) and connect the camera via usb I get the above messages. The few times I have managed to connect to the camera I was able to get 10 or so photos over before the router lost the connect to the camera. Sadly I don't have the logs from this situation.

I will try refreshing the router (I've only done the factory flash at this point) There is not much to the flashing process I not sure how I would have done it wrong. Upload file via web interface. . . . wait for reboot. . . connect.

[GonzoG]

With only "factory" image router might not work correctly. I always flash both firmware images.

Also check other USB cables. I've got similar problem with bad cable.