dslrdashboard.info

Posted: **26 Jul 2016, 07:25**

Help please. I can't get this combination working. I can access the router from the iOS devices (tried it with an iPhone 6s and an iPad mini) but i don't get any connection to the camera. I'm using a USB-cable that was working fine with qDDB running on a Windows notebook and the D600. The router is the one from Photecs with the pre-installed alternative firmware.

I connect to the WLAN the router sets up, press the Wifi connection button (long), the menu pops up (with the correct IP), i hit OK and nothing happens.

qDDB Version is 3.5.1, the camera a D600, iOS 9.3.2

Thanks four your help!

Posted: **27 Jul 2016, 21:26**

Check in router system log if camera is connected and correctly recognized.

Posted: **30 Jul 2016, 09:17**

This is the log.

What does this mean?
Sep 8 15:44:36 OpenWrt kern.err kernel: [ 43.930000] usb 1-1: device not accepting address 4, error -71
Sep 8 15:44:36 OpenWrt kern.info kernel: [ 44.050000] usb 1-1: new high-speed USB device number 5 using ehci-platform
Sep 8 15:44:36 OpenWrt kern.err kernel: [ 44.470000] usb 1-1: device not accepting address 5, error -71
Sep 8 15:44:36 OpenWrt kern.err kernel: [ 44.470000] hub 1-0:1.0: unable to enumerate USB device on port 1

Sep 8 15:44:04 OpenWrt syslog.info syslogd started: BusyBox v1.19.4
Sep 8 15:44:04 OpenWrt kern.notice kernel: klogd started: BusyBox v1.19.4 (2014-07-11 18:33:29 CEST)
Sep 8 15:44:04 OpenWrt kern.notice kernel: [ 0.000000] Linux version 3.3.8 (hubaiz@xandroid64) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Fri Jul 11 18:39:12 CEST 2014
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.000000] MyLoader: sysp=fa89c804, boardp=69cd3b24, parts=31a09c82
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] bootconsole [early0] enabled
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] SoC: Atheros AR9330 rev 1
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Determined physical RAM map:
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] memory: 02000000 @ 00000000 (usable)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Sep 8 15:44:04 OpenWrt kern.warn kernel: [ 0.000000] Zone PFN ranges:
Sep 8 15:44:04 OpenWrt kern.warn kernel: [ 0.000000] Normal 0x00000000 -> 0x00002000
Sep 8 15:44:04 OpenWrt kern.warn kernel: [ 0.000000] Movable zone start PFN for each node
Sep 8 15:44:04 OpenWrt kern.warn kernel: [ 0.000000] Early memory PFN ranges
Sep 8 15:44:04 OpenWrt kern.warn kernel: [ 0.000000] 0: 0x00000000 -> 0x00002000
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.000000] On node 0 totalpages: 8192
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 802d61e0, node_mem_map 81000000
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.000000] Normal zone: 64 pages used for memmap
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.000000] Normal zone: 8128 pages, LIFO batch:0
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Sep 8 15:44:04 OpenWrt kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Sep 8 15:44:04 OpenWrt kern.notice kernel: [ 0.000000] Kernel command line: board=TL-MR3040 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Sep 8 15:44:04 OpenWrt kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Sep 8 15:44:04 OpenWrt kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Memory: 29116k/32768k available (2115k kernel code, 3652k reserved, 406k data, 208k init, 0k highmem)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] NR_IRQS:51
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.080000] pid_max: default: 32768 minimum: 301
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.080000] Mount-cache hash table entries: 512
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.090000] NET: Registered protocol family 16
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.100000] MIPS: machine is TP-LINK TL-MR3040
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.350000] bio: create slab <bio-0> at 0
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.360000] Switching to clocksource MIPS
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.360000] NET: Registered protocol family 2
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.370000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.370000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.380000] TCP: Hash tables configured (established 1024 bind 1024)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.390000] TCP reno registered
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 0.400000] NET: Registered protocol family 1
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 0.410000] PCI: CLS 0 bytes, default 32
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 9.450000] ath: Country alpha2 being used: US
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 9.450000] ath: Regpair used: 0x3a
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 9.450000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sep 8 15:44:04 OpenWrt kern.debug kernel: [ 9.460000] Registered led device: ath9k-phy0
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.460000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.460000] cfg80211: Calling CRDA for country: US
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.470000] cfg80211: Regulatory domain changed to country: US
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.470000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.480000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.490000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.500000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.500000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.510000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.520000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.580000] PPP generic driver version 2.4.2
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 9.820000] ip_tables: (C) 2000-2006 Netfilter Core Team
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.040000] NET: Registered protocol family 24
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.060000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.070000] ehci-platform ehci-platform: Generic Platform EHCI Controller
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.070000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.110000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.130000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.130000] hub 1-0:1.0: USB hub found
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.130000] hub 1-0:1.0: 1 port detected
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.160000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
Sep 8 15:44:04 OpenWrt kern.info kernel: [ 10.390000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sep 8 15:44:06 OpenWrt daemon.notice netifd: Interface 'lan' is now up
Sep 8 15:44:07 OpenWrt kern.info kernel: [ 14.880000] device eth0 entered promiscuous mode
Sep 8 15:44:07 OpenWrt daemon.notice netifd: Interface 'loopback' is now up
Sep 8 15:44:07 OpenWrt user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sep 8 15:44:12 OpenWrt kern.info kernel: [ 20.270000] device wlan0 entered promiscuous mode
Sep 8 15:44:12 OpenWrt kern.info kernel: [ 20.310000] br-lan: port 2(wlan0) entered forwarding state
Sep 8 15:44:12 OpenWrt kern.info kernel: [ 20.320000] br-lan: port 2(wlan0) entered forwarding state
Sep 8 15:44:14 OpenWrt kern.info kernel: [ 22.320000] br-lan: port 2(wlan0) entered forwarding state
Sep 8 15:44:15 OpenWrt authpriv.info dropbear[859]: Running in background
Sep 8 15:44:17 OpenWrt auth.err sshd[865]: error: Bind to port 22 on 0.0.0.0 failed: Address already in use.
Sep 8 15:44:17 OpenWrt auth.crit sshd[865]: fatal: Cannot bind any address.
Sep 8 15:44:19 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Sep 8 15:44:19 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Sep 8 15:44:22 OpenWrt daemon.info dnsmasq[922]: started, version 2.66 cachesize 150
Sep 8 15:44:22 OpenWrt daemon.info dnsmasq[922]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Sep 8 15:44:22 OpenWrt daemon.info dnsmasq-dhcp[922]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sep 8 15:44:22 OpenWrt daemon.info dnsmasq[922]: using local addresses only for domain lan
Sep 8 15:44:22 OpenWrt daemon.warn dnsmasq[922]: no servers found in /tmp/resolv.conf.auto, will retry
Sep 8 15:44:22 OpenWrt daemon.info dnsmasq[922]: read /etc/hosts - 1 addresses
Sep 8 15:44:22 OpenWrt daemon.info dnsmasq-dhcp[922]: read /etc/ethers - 0 addresses
Sep 8 15:44:22 OpenWrt user.info sysinit: setting up led USB
Sep 8 15:44:22 OpenWrt user.info sysinit: setting up led WLAN
Sep 8 15:44:22 OpenWrt user.info sysinit: setting up led LAN
Sep 8 15:44:22 OpenWrt user.info sysinit: Starting DslrDashboardServer (ddserver)
Sep 8 15:44:22 OpenWrt user.info sysinit: Saving PID 938 to /var/run/ddserver.pid
Sep 8 15:44:22 OpenWrt user.info sysinit: DslrDashboard server started
Sep 8 15:44:23 OpenWrt user.info syslog: DslrDashboardServer starting
Sep 8 15:44:23 OpenWrt user.info syslog: Starting socket server on port 4757
Sep 8 15:44:23 OpenWrt user.info syslog: Awaiting client connection
Sep 8 15:44:23 OpenWrt user.info syslog: Starting UDP listener
Sep 8 15:44:23 OpenWrt user.info syslog: join multicast group: 224.1.2.3
Sep 8 15:44:35 OpenWrt kern.info kernel: [ 43.010000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sep 8 15:44:35 OpenWrt kern.info kernel: [ 43.260000] usb 1-1: new high-speed USB device number 3 using ehci-platform
Sep 8 15:44:35 OpenWrt kern.info kernel: [ 43.510000] usb 1-1: new high-speed USB device number 4 using ehci-platform
Sep 8 15:44:36 OpenWrt kern.err kernel: [ 43.930000] usb 1-1: device not accepting address 4, error -71
Sep 8 15:44:36 OpenWrt kern.info kernel: [ 44.050000] usb 1-1: new high-speed USB device number 5 using ehci-platform
Sep 8 15:44:36 OpenWrt kern.err kernel: [ 44.470000] usb 1-1: device not accepting address 5, error -71
Sep 8 15:44:36 OpenWrt kern.err kernel: [ 44.470000] hub 1-0:1.0: unable to enumerate USB device on port 1
Sep 8 15:44:47 OpenWrt kern.info kernel: [ 55.540000] usb 1-1: new high-speed USB device number 6 using ehci-platform
Sep 8 15:44:47 OpenWrt kern.info kernel: [ 55.790000] usb 1-1: new high-speed USB device number 7 using ehci-platform
Sep 8 15:44:48 OpenWrt kern.info kernel: [ 56.040000] usb 1-1: new high-speed USB device number 8 using ehci-platform
Sep 8 15:44:48 OpenWrt kern.err kernel: [ 56.460000] usb 1-1: device not accepting address 8, error -71
Sep 8 15:44:48 OpenWrt kern.info kernel: [ 56.580000] usb 1-1: new high-speed USB device number 9 using ehci-platform
Sep 8 15:44:49 OpenWrt kern.err kernel: [ 57.000000] usb 1-1: device not accepting address 9, error -71
Sep 8 15:44:49 OpenWrt kern.err kernel: [ 57.000000] hub 1-0:1.0: unable to enumerate USB device on port 1
Sep 8 15:45:18 OpenWrt daemon.info hostapd: wlan0: STA e4:8b:7f:a6:f1:33 IEEE 802.11: authenticated
Sep 8 15:45:18 OpenWrt daemon.info hostapd: wlan0: STA e4:8b:7f:a6:f1:33 IEEE 802.11: associated (aid 1)
Sep 8 15:45:21 OpenWrt daemon.info dnsmasq-dhcp[922]: DHCPDISCOVER(br-lan) e4:8b:7f:a6:f1:33
Sep 8 15:45:21 OpenWrt daemon.info dnsmasq-dhcp[922]: DHCPOFFER(br-lan) 192.168.1.209 e4:8b:7f:a6:f1:33
Sep 8 15:45:21 OpenWrt daemon.info dnsmasq-dhcp[922]: DHCPDISCOVER(br-lan) e4:8b:7f:a6:f1:33
Sep 8 15:45:21 OpenWrt daemon.info dnsmasq-dhcp[922]: DHCPOFFER(br-lan) 192.168.1.209 e4:8b:7f:a6:f1:33
Sep 8 15:45:22 OpenWrt daemon.info dnsmasq-dhcp[922]: DHCPREQUEST(br-lan) 192.168.1.209 e4:8b:7f:a6:f1:33
Sep 8 15:45:22 OpenWrt daemon.info dnsmasq-dhcp[922]: DHCPACK(br-lan) 192.168.1.209 e4:8b:7f:a6:f1:33 MiniPad
Sep 8 15:45:37 OpenWrt user.info syslog: recv: 57
Sep 8 15:45:37 OpenWrt user.info syslog: Client multicast query DslrDashboardClient{ba9b851e-a2ee-4620-9ab3-f521c7fb94e6}
Sep 8 15:45:37 OpenWrt user.info syslog: Server message length: 57 msg: DslrDashboardServer{ba9b851e-a2ee-4620-9ab3-f521c7fb94e6}
Sep 8 15:45:37 OpenWrt user.info syslog: Incoming client connection
Sep 8 15:45:37 OpenWrt user.info syslog: Awaiting client connection
Sep 8 15:45:37 OpenWrt user.info syslog: USB Devices in
Sep 8 15:45:37 OpenWrt user.info syslog: Number of possible configurations: 1 Device Class: 9 VendorID: 7531, ProductID: 2
Sep 8 15:45:37 OpenWrt user.info syslog: Number of alternate settings:
Sep 8 15:45:37 OpenWrt user.info syslog: Interface class: 9 Interface number: 0 Number of endpoints: 1
Sep 8 15:45:37 OpenWrt user.info syslog: Imaging USB devices found: 0
Sep 8 15:45:37 OpenWrt user.err syslog: Error reading total packet size: 0
Sep 8 15:45:37 OpenWrt user.err syslog: Stoping client
Sep 8 15:45:39 OpenWrt user.info syslog: Closing USB device
Sep 8 15:45:45 OpenWrt user.info syslog: Incoming client connection
Sep 8 15:45:45 OpenWrt user.info syslog: Awaiting client connection
Sep 8 15:45:45 OpenWrt user.info syslog: USB Devices in
Sep 8 15:45:45 OpenWrt user.info syslog: Number of possible configurations: 1 Device Class: 9 VendorID: 7531, ProductID: 2
Sep 8 15:45:45 OpenWrt user.info syslog: Number of alternate settings:
Sep 8 15:45:45 OpenWrt user.info syslog: Interface class: 9 Interface number: 0 Number of endpoints: 1
Sep 8 15:45:45 OpenWrt user.info syslog: Imaging USB devices found: 0
Sep 8 15:45:45 OpenWrt user.err syslog: Error reading total packet size: 0
Sep 8 15:45:45 OpenWrt user.err syslog: Stoping client
Sep 8 15:45:47 OpenWrt user.info syslog: Closing USB device

dslrdashboard.info

D600+TL-MR340+iOS = No connection

D600+TL-MR340+iOS = No connection

Re: D600+TL-MR340+iOS = No connection

Re: D600+TL-MR340+iOS = No connection